Shop
Showing 721–744 of 814 resultsSorted by popularity
-
Relay Modules, RF/NRF/RFID Modules
433MHz 12V 1 Channel Relay Module Wireless Remote Control Switch with Battery
-17%
Relay Modules, RF/NRF/RFID Modules433MHz 12V 1 Channel Relay Module Wireless Remote Control Switch with Battery
- Operating voltage: DC 12V
- Operating temperature: -40~80 degrees
- Operating frequency: 433MHZ Receive sensitivity: ≥-95dB
- Working Mode: jump switch, point action, self-locking, and interlocking(adjustable)
SKU: n/a -
Color Sensor
TCS3200 Colour Recognition Sensor Module
- Operating Voltage: 3V-5V
- High-resolution conversion of light intensity to frequency.
- Chip pins all has drawn for standard 100.
- Put the needle (2.54 mm).
- Mil-convenient for bitmap board.
- Programmable color and full-scale output frequency.
- Communicate directly with a microcontroller.
- Low-profile surface mount package.
SKU: EB2026 -
Water & Moisture Sensors
Soil Moisture Sensor Detector Module Soil Moisture Humidity Test Sensor with 1.3M Cable
Water & Moisture SensorsSoil Moisture Sensor Detector Module Soil Moisture Humidity Test Sensor with 1.3M Cable
- Operating Voltage: 3.3V to 5V DC
- Operating Current: 15mA
- Output Digital – 0V to 5V, Adjustable trigger level from preset
- Output Analog – 0V to 5V based on infrared radiation from fire flame falling on the sensor
- LEDs indicating output and power
- PCB Size: 3.2cm x 1.4cm
- LM393 based design
- Easy to use with Microcontrollers or even with normal Digital/Analog IC
- Small, cheap and easily available
SKU: n/a -
Interfacing Modules
TJA1050 CAN Controller Bus Driver Interface Module
- Onboard TJA1050 CAN controller interface chip
- Chip commonly used pin has led, convenient connection to use
- Pin 5 v to the power supply
- PCB board size: 22 (mm) x11.5 (mm)
- Fully compatible with the ISO 11898 standard
- High speed (up to 1 Mbaud)
SKU: n/a -
Tools & Miscellaneous Parts
Standard 60 Watt Corded Glue Gun with 5 Glue Sticks
- Feed Type Trigger-fed Gun
- Rated Power: 60 W
- Heating Up Time: 5 min
- Cord Length: 1 Mtr.
- Aluminum Tip
- Replaceable Cartridge(Glue Sticks)
- Specific Uses of the Product Wood, Plastics, Textiles, Cardboard, Ceramics, Leather, etc
SKU: n/a -
Other Modules
DSO138 2.4″ TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered
-10%
Other ModulesDSO138 2.4″ TFT Handheld Pocket-size Digital Oscilloscope Kit DIY Parts Electronic Learning Set Soldered
- This kit uses ARM Cortex-M3 processor (STM32F103C8), and includes a 2.4-inch color TFT display screen.
- Adjustable vertical displacement, and with instructions.
- With automatic, regular and one-shot modes, easy to capture the moment waveform.
- Available rising or falling edge trigger.
- Observable previous trigger waveform (negative delay).
- Can freeze at any time waveform display (the HOLD function).
- Maximum Real-time Sampling Rate: 1Msps
- Accuracy: 12Bit
- Sampling Buffer Depth: 1024 bytes
- Analog Bandwidth: 0-200KHz
SKU: n/a -
-
Arduino Shields
Proto Shield (Prototype) for Arduino Uno Mini Breadboard
- It has a nice standard 0.1″x0.1″ prototyping grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- An IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- Two 3mm general use LEDs, red and green, as well as 2 matching resistors
SKU: EB3030 -
Boards & Programmers
Digispark ATTINY85 Mini USB Development Board
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 512 Bytes In-System Programmable EEPROM
- 512 Bytes Internal SRAM
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- 4 Single Ended Channels
- Two Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
SKU: n/a -
