Shop
Showing 625–648 of 814 resultsSorted by popularity
-
-
-
Display Devices
3.5″ inch ILI9486 TFT Touch Shield LCD Module 480×320 for Arduino Uno
- 3.5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
- It can control the backlight to connect the transistor to a digital pin
- 480×320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade
- 4-wire resistive touchscreen
- 8-bit digital interface, plus 4 control lines
SKU: n/a -
PCB & Soldering
TE-801 Multi-function LED Magnifier PCB Soldering iron Stand Holder Table Magnifying glass 35X 12X w/ 2-LED Light
PCB & SolderingTE-801 Multi-function LED Magnifier PCB Soldering iron Stand Holder Table Magnifying glass 35X 12X w/ 2-LED Light
- A useful Aid for soldering work or model makers
- Battery required for light: 3 x AAA
- Adjustable crocodile holding clamps
- The bottom battery compartment is furnished with steel plate which can enhance stability
- Ideal when a third hand is needed
- With two LED lighting, this model can work very well in the dark environment
SKU: EB895 -
-
Arduino Shields
Sensor Shield V5 Expansion Board For Arduino
- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
- APC220 wireless rf modules communication interface
- RB URF v1.1 ultrasonic sensors interface
- 12864 LCD string of line and parallel interface
- 32 servo controller interface
SKU: n/a -
RF/NRF/RFID Modules
315MHZ Four Key Wireless Smart Car Remote Control Kit
- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- TransmitterRadiated power: 10mW at 12V.
- Transmission distance (m): 3 to 5.
SKU: n/a -
Arduino Shields
CNC Shield V3 Engraving Machine 3D Printer A4988 DRV8825 Driver Expansion Board
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: EB3012 -
Other Modules
SW520D Tilt Sensor Module
- IC Chip: LM393
- Operating Voltage: 5V / 3.3V
- PCB Size: 3.2cm x 1.4cm
- Output Format: Digital switching outputs (0 and 1)
- Signal Detection Sensitivity: Adjustable using a potentiometer
- Output Driving Ability: More than 15mA
- Sensor Type: SW-520D Tilt Vibration Sensor
SKU: EB1013
![Analog pH Sensor Kit For Arduino [Module + Electrode]](https://ebhoot.in/wp-content/uploads/2023/10/analog-ph-sensor-meter-kit-for-arduino-robotics-bangladesh-300x300.jpg)
