Electronics Modules
Showing 73–96 of 117 resultsSorted by popularity
-
-
Other Modules
SW520D Tilt Sensor Module
- IC Chip: LM393
- Operating Voltage: 5V / 3.3V
- PCB Size: 3.2cm x 1.4cm
- Output Format: Digital switching outputs (0 and 1)
- Signal Detection Sensitivity: Adjustable using a potentiometer
- Output Driving Ability: More than 15mA
- Sensor Type: SW-520D Tilt Vibration Sensor
SKU: EB1013 -
-
-
Amplifier Modules, Interfacing Modules
TXS0108E High Speed Full Duplex 8 Channel Logic Level Converter
Amplifier Modules, Interfacing ModulesTXS0108E High Speed Full Duplex 8 Channel Logic Level Converter
- VCCA Voltage level: 1.2V-3.6V
- VCCB Voltage level: 1.65V-5.5V
- It can provide 3.3-5V, 1.8-3.3V level conversion
- Dimension Approx: 26 x 15 mm
- PCB Color: Blue
- 8-bit bi-directional 3.3V-5V/5V-
- 3.3V logic level converter board
- Serial communication interface compatible with UART/IIC/SPI port easily to connect
SKU: EB1008 -
Relay Modules, RF/NRF/RFID Modules
433MHz 12V 1 Channel Relay Module Wireless Remote Control Switch with Battery
-17%
Relay Modules, RF/NRF/RFID Modules433MHz 12V 1 Channel Relay Module Wireless Remote Control Switch with Battery
- Operating voltage: DC 12V
- Operating temperature: -40~80 degrees
- Operating frequency: 433MHZ Receive sensitivity: ≥-95dB
- Working Mode: jump switch, point action, self-locking, and interlocking(adjustable)
SKU: n/a -
Interfacing Modules
MAX485 TTL to RS485 Converter Module
- On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
- A low power consumption for the RS-485 communication
- Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
- Slew-rate limited transceiver
- All pins of the chip have been lead to can be controlled through the microcontroller.
- Convenient RS-485 communication wiring
- Multiple Units can be connected to the same RS-485 bus wiring.
- All Chip pins are brought out for proper controls
SKU: EB3098 -
Motor Driver Modules
PCA9685 16-Channel 12-Bit PWM/Servo Driver I2C Interface
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: EB5658 -
Interfacing Modules
CJMCU TCA9548A I2C 8 Channel Multiple Extensions Development Board
- 5V Tolerant Inputs.
- Supports Hot Insertion.
- I2C Bus and SMBus Compatible.
- Low Standby Current.
- 1-to-8 Bidirectional Translating Switches.
- Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II.
- Active-Low Reset Input.
- Power Up With All Switch Channels Deselected.
SKU: n/a -
Buck/ Boost Converters
LM2596 2A Buck Step-Down Power Converter Module DC 4 ~ 40 to 1.3-37V LED Voltmeter
Buck/ Boost ConvertersLM2596 2A Buck Step-Down Power Converter Module DC 4 ~ 40 to 1.3-37V LED Voltmeter
- Input Voltage(VDC): 4 ~ 40.
- Output Voltage(VDC): 1.3 ~ 37.
- Output Current: 2A Rated, ( 3A maximum with heat sink).
- Switching Frequency: 150 kHz.
- Input reverse polarity protection.
- Built-in output short protection function.
SKU: EB1004 -
-
BMS Module / Battery Charging Module
2S 4A BMS Li-Ion Battery Protection Board With Nickel Strip
- Battery Configuration: 2-series (2S) lithium-ion battery packs
- Maximum Continuous Discharge Current: 4A
- Protection Features: Overcharge protection, overdischarge protection, short circuit protection, overcurrent protection
- Dimensions: Typically specified in millimeters (mm), e.g., 50mm x 20mm x 3mm
- Material: Usually made of durable PCB (Printed Circuit Board) material
- Included Components: Pre-welded nickel strip for easy connection
- Application: Designed for managing and protecting small-scale lithium-ion battery packs
SKU: n/a -
RF/NRF/RFID Modules
315MHZ Four Key Wireless Smart Car Remote Control Kit
- No. of the channel: 4
- Operating mode: Non-Locking
- Receiver Operating voltage: DC 5V.
- Receiver sensitivity is: -98dB.
- Transmitter Operating voltage: DC 12V
- Transmitting frequency: 315 MHZ.
- Transmitter Operating current: 10mA at 12V.
- TransmitterRadiated power: 10mW at 12V.
- Transmission distance (m): 3 to 5.
SKU: n/a -
Amplifier Modules
JQ6500 Voice Module MP3 Module MCU Serial Port Control Broadcast one-on-one 5 Way Control Music IC 16Mbit
-14%
Amplifier ModulesJQ6500 Voice Module MP3 Module MCU Serial Port Control Broadcast one-on-one 5 Way Control Music IC 16Mbit
- MP3 file format:
- support all bit rate 11172-3 and ISO13813-3 layer3 audio decoding
- Sample rate support (KHZ): 8/11.025/12/16/22.05/24/32/44.1/48
- support Normal, Jazz, Classical, Pop, Rock and other sound effects
- UART interface: standard serial port, TTL level, baud rate can be set
- Input voltage: 3.2V-5V (best 4.2V);
- Rated current: 20ma
SKU: EB1064 -
